Hvorfor har den anden part svært ved at høre mig?
Kontroller, at mute-kontakten står i taleposition. Kontroller placeringen af headsettets mikrofonarm, og placer den ca. 2 cm fra din underlæbe. Mikrofonlydstyrken kan være for lav.
Toshiba phones with GN 1200 must be properly configured to Answer/Release a call
How to program the button setting/changing a Flexible Button’s Function
1. Press #9876 to enter User Programming Mode.
2. Press Hold.
3. Press the Flexible Button to set or change.
4. Enter the Flexible Button Code 280 (Release/Answer)
5. Press the same Flexible Button (flashing) to save the setting. “DATA PROGRAMMED” appears on your LCD.
The installing dealer can also use Network eManager to program the button. They would connect to the CIX and do the following:
1. Select Station and then Station Assignments
2. Select the DN they want to change from the list on the left
3. Select the Key tab
4. Select an empty button
5. Select Call control from the right window
6. Click on Release/Answer
7. Click submit
How is the GN 8050 connected to the telephone?
{gnresource:HSS_8050-04_klein}
Connection:
Take the RJ10 cable connection with RJ10 and plug one end of the cable into the jack marked "telephone icon" of the repeater.
Disconnect the handset cable from the telephone and connect one end into the jack
marked "handset device" jack of the repeater.
Now plug the other end of the RJ10 cable into the handset jack of the telephone.
{gnresource:HSS_GN2100-an-GN8000-Anschlussbild-448x256(1)}
Now open the cover of the repeater. On the right side is the Battery compartment into which you must insert the provided batteries.
The battery storage switch (A B C) can help in extending the life of the battery.
{gnresource:HSS_GN8210_schalter_ABC_klein}
A: Battery charger is enabled / charging through incoming signal
B: Battery charge is enabled / charging through incoming signal
B: Battery charging switch is SWITCHED OFF
You can also operate the GN 8050 with a power supply instead of the batteries.
The article number for this is 26-0098
If, subsequently, you hear a threefold audio signal in the Headset, this will be an indication of low battery power.
Headset:
Now connect the quick-disconnector of the headset to the quick-disconnector the connector cable.
{gnresource:HSS_GN2100_anschlussQD}
Setting the telephone:
To test the function, put the headset on and take the receiver of the telephone. Now set the switch Telephone/Computer to " Telephone "
If no distinct dial tone is heard in the headset, operate the compatibility switch (which is under the battery compartment) from A- I
till you receive a clear dial tone in the headset.
{gnresource:HSS_SchalterGN8000(A-I)
Setting the microphone volume:
To set the microphone/ transmission volume set the mute button to "speak" and make a call to someone, if the person you call does not hear you very clearly, then operate the volume control from 1-8 till they can hear you clearly.
{gnresource:HSS_GN8000_Regler_Sendelautst?rke_klein(1)}
Setting the volume:
You can set your desired volume with the reception volume control.
{gnresource:HSS_GN8000_Empfangslautst?rke_klein}
Setting PC:
Take the PC connection cable (3,5 mm jack with 2x3,5 mm jack) and plug the individual end of the Y-cable into the jack marked "computer" on the rearside of the repeater.
Then plug the green jack connector into the jack marked "microphone icon" and the black jack connector Plug into the jack marked " speaker or headset icon of your computer.
Function:
Telephone icon: Headset operation:
Telephone icon: simultaneously with the Headset telephone &Audio applications
Computer icon: Speech/audio application
{gnresource:HSS_GN8050_Schalter_Tel_PC_orginal}
You can set the volume of the computer signal with the reception volume control.
{gnresource:HSS_GN8050_PC_lautstärkenregler_klein}
For the Receiver operation the Telephone/computer switch must be set to
" Computer" .
Which Headset/cord can be used with the Temporis 5000?
As the Temporis has both an RJ9port and RJ45 data port, the cord 8800-00-25 and the GN 1200 can be used.
Jabra GN8210: Hvorfor har jeg svært ved at høre den anden part, eller hvorfor lyder han/hun anderledes?
Afhængig af den valgte lydtilstand kan indgangslydstyrken forekomme lav i forhold til, hvad du er vant til. Hvis du har valgt TT-4-beskyttelsestilstand (indstilling C), skal du være opmærksom på, at denne tilstand er en meget nøje beskyttelsesstandard, der er udviklet til at forbedre sikkerheden overfor høreskader.
Hvorfor hører jeg et ekko i mit headset, når jeg taler?
Mikrofonlydstyrken kan være for høj. Løft forstærkerens topdæksel, og drej knappen til mikrofonlydstyrke mod venstre til et lavere tal.
Hvorfor lyser eller blinker online-indikatoren ikke?
Kontroller, at headsetholderens/online-indikatoren er sat helt ind i porten bag på forstærkeren. Kontroller, at batterierne er sat korrekt i. Udskift batterierne med nye.
Jabra GN9300: Hvordan justerer jeg klartonen?
Tag headsettet på. Løft røret og lyt efter opkaldstonen i headsettet. Fortsæt justeringen, hvis du ikke hører en opkaldstone, eller hvis den er utydelig. Tag basedækslet af og find kontakten til klartone. Drej kontakten (gennem indstilling A til G), til opkaldstonen er tydelig.
How is the GN 8000 connected to the telephone?
{gnresource:HSS_GN8000_foto_klein}
Connection:
Take the RJ10 cable connection with RJ10 and plug one end of the cable
into the jack "marked telephone icon" of the repeater.
Disconnect the handset cable from the telephone and plug this into the jack
"marked handset" of the repeater.
Now plug the other end of the RJ10 cable into the handset jack of the telephone.
{gnresource:HSS_GN2100-an-GN8000-Anschlussbild-448x256(1)}
Now open the cover of the repeater. On the right side is the Battery compartment into which you must insert the batteries provided.
The battery storage switch (A B C) can help in extending the life of the battery.
{gnresource:HSS_GN8210_schalter_ABC_klein}
A: Battery charger is enabled / charging through incoming signal
B: Battery charge is enabled / charging through incoming signal
B: Battery charging switch is SWITCHED OFF
You can also operate the GN 8000 with a power supply instead of the batteries.
The article number for this is 26-0098
If, subsequently, you hear a threefold audio signal in the Headset, this will be an indication of low battery power.
Headset:
Now connect the quick-disconnector of the headset to the quick-disconnector of the connector cable.
{gnresource:HSS_GN2100_anschlussQD}
Setting the telephone:
To test the function, put the headset on and take the receiver of the telephone. Now set the switch headset/receiver to "Headset."
If no clear dial tone is heard in the headset, operate the compatibility switch (which is under the battery compartment) from A-I
till a clear dial tone is received in the headset.
{gnresource:HSS_SchalterGN8000(A-I)}
Setting the microphone volume:
To set the microphone/transmission volume, set the mute button to "speak"and make a call to someone. If the person you call does not hear you very clearly, then operate the volume control from 1-8 till they can hear you clearly.
{gnresource:HSS_GN8000_Regler_Sendelautstärke_klein(1)}
Setting the volume:
{gnresource:HSS_GN8000_Empfangslautstärke_klein}
You can set the desired volume with volume reception control.
Hvorfor lyder der bip i mit headset?
En biplyd i headsettet kan være en advarsel om, at batterierne i forstærkeren er ved at være brugt op. Udskift begge batterier. Brug kun alkaline-batterier af størrelse AA.
Jabra GN8000 serien: Hvorfor hører jeg min egen stemme i mit headset, når jeg taler?
Mikrofonlydstyrken kan være indstillet for højt. Løft topdækslet på Jabra GN8000/GN8050/GN8210, og drej knappen til mikrofonlydstyrke mod uret til et lavere tal.
Hvorfor lyder der bip i mit headset?
En biplyd i headsettet kan være en advarsel om, at batterierne i forstærkeren er ved at være brugt op. Udskift begge batterier. Brug kun batterier af størrelse AA.
Jabra GN8210: Hvorfor har den anden part svært ved at høre mig?
Kontroller, at mute-kontakten står i taleposition. Kontroller placeringen af headsettets mikrofonarm, og at den er placeret ca. 2 cm fra din mund. Sendelydstyrken kan være indstillet for lavt. Løft forstærkerens topdæksel, og juster
How is the GN 8210 connected to the telephone?
{gnresource:HSS_GN8210-Bild-WG}
Connection:
Take the connection cable RJ10 with RJ10 and plug one end of the cable into the jack marked "Telephone icon" of the repeater.
Now disconnect the handset cable from the telephone and plug this into the jack marked
"handset" of the repeater.
Now Plug the other end of RJ10 cable into the handset jack of the telephone.
{gnresource:HSS_GN2100-an-GN8000-Anschlussbild-448x256(1)}
By means of the selector switch (A B C ) you can take account of the EU guideline (85 dB).
{gnresource:HSS_GN8210_schalter_ABC_klein}
A: Increased high frequencies
B: Clear digital understanding
C: Highest hearing protection (Australian standard TT-4)
Thanks to the DSP (Digital signal processor) background noise or interference is filtered out.
Headset:
Now connect the quick-disconnector of the headset to that of the connector cable.
{gnresource:HSS_GN2100_anschlussQD}
Setting the telephone:
To test the function, put the headset on and take the receiver of the telephone. Now set the switch headset/receiver to "Headset".
If no clear dial tone is heard in the headset, operate the compatibility switch from A-I till a clear dial tone is received in the headset.
{gnresource:HSS_SchalterGN8000(A-I)}
Setting the microphone volume:
To set the microphone/ transmission volume, set the mute button to "speak" and make a call to someone. If the person you call does not hear you very clearly, then operate the volume control from 1-8 till they can hear you clearly.
{gnresource:HSS_GN8000_Regler_Sendelautstärke_klein(1)}
Setting the volume:
You can set your desired hearing volume using the reception volume control .
{gnresource:HSS_GN8000_Empfangslautstärke_klein}
Hvorfor kan jeg ikke høre en opkaldstone, når headsettet er tændt?
Kontroller, at du har sat både headsettets og rørets ledning i de korrekte porte. Kontroller, at headset-/rørkontakten står i headsetstilling. Kontroller, at batterierne er sat korrekt i. Udskift batterierne med nye.
Hvorfor kan jeg ikke høre en opkaldstone, når headsettet er tændt?
Kontroller, at du har sat både headsettets og rørets ledning i de korrekte porte. Kontroller, at headset-/rørkontakten står i headsetstilling. Kontroller, at batterierne er sat korrekt i. Udskift batterierne med nye. Du
Hvorfor hører jeg et ekko i mit headset, når jeg taler?
Sendelydstyrken kan være for høj. Løft forstærkerens topdæksel, og drej knappen til sendestyrke mod venstre til et lavere tal.
Hvorfor har den anden part svært ved at høre mig?
Kontroller, at mute-kontakten står i taleposition. Kontroller placeringen af headsettets mikrofonarm, og placer den ca. en fingerbredde fra din underlæbe. Sendelydstyrken kan være for lav. Løft forstærkerens topdæksel
Jabra GN8210 er en digital forstærker - kan jeg bruge den sammen med både analog og digitale telefonsystemer?
Ja, Jabra GN8210 fungerer sammen med både analoge og digitale telefonsystemer
Hvorfor virker mit stemmegenkendelsesprogram ikke ordentligt?
Stemmegenkendelsesprogrammet har visse begrænsninger hvad angår forståelse af tale. For at forbedre resultatet skal du placere mikrofonen foran din mund en fingerbredde fra læberne. Juster mikrofonens følsomhedsindstillinger på computeren. Kontakt din softwa